cfsoli.blogg.se

1. #Tam valley octopus iii with rocrail driver#
2. #Tam valley octopus iii with rocrail code#
3. #Tam valley octopus iii with rocrail Pc#

You can also use a "Y" to connect two servos to one output (works great for passing sidings!). You can use "Y" cords to use more than one fascia controller to control one servo. This gives you a simple way to hook up the inputs to the board using servo-style cords and extensions. You can use the same fascia controllers as the Quad. Power input is any power supply from 7.0-24 volts DC.

This means less heat and a lower power draw.

The Octopus III has an on-board high-frequency switching 1.8A power supply that is more efficient than the old linear power supply. The board also has jumpers for setting the range from +/-20 degrees around center to +/70 degrees and for centering the servo to simplify installation for applications where there are no hard endpoints or where you are using the same turnouts in all locations. This item appears to not currently be in stock But is still available to order. more info on Octocoder DCC Add-on Decoder. No frills just throws the turnouts from your throttle or JMRI. By adding this DCC stationary/accessory decoder to the Octopus you can control your turnouts with servos and DCC at the lowest possible cost per turnout. Use servo extension cables to plug in to Octopus III controller ports. In order to get the colors of the LEDs correct note that they have a flat side which is corresponds to the flat line on the back side of the board. With the Remote Aligner you can set the amount of force used in the automatic alignment to match your rail size and the servos you are using. Tam Valley - Octocoder DCC Add-on Decoder. The 3-lead LEDs and the push-button switch are not mounted so that you can arrange them on your panel as you wish. This allows each servo to be adjusted to its optimum range and endpoints and each servo can be independently adjusted. The servo endpoints are found automatically by searching for hard endpoints or you can manually align them with the Remote Aligner. No more hanging under the layout trying to push buttons. The Remote Aligner allows you to stand by the turnout being aligned so you can precisely align the servo endpoints with ease. There are 8 positions for plugging in R/C type servos and 8 inputs for switches or 5V logic. The Octopus III can drive up to 8 servos to move turnouts or other devices on your layout controlled by a toggle switch, a momentary pushbutton, the output of a signal system or a DCC decoder.

#Tam valley octopus iii with rocrail driver#

The relays areīuffered by a ULN2803 Darlington transistor array that also providesĭiode flyback protection.Octopus III Eight Servo Driver with Remote Aligner Tool An example would be a crossing gate that isĪctivated when a turnout is in a particular position. However, the relays can be used to control any device thatĭraws up to 1 amp. The relays are optional and are designed to be used to power more info on Remote Aligner for Octopus III. Comes with a 7' cable which allows you to stand next to your turnout while aligning the servo. Just one of these needed for all of your Octopus IIIs. The control pulses for the servos (SRV1-8) are Used with the Octopus III for alignment of servos (cannot be used with the Octopus II). The input can be any open collector logic that is active low. Power is input through a bridge rectifier which allows the use of DC or AC voltage. Learn more about the SX chip and SX/B, the BASIC language for SX at the Parallax website. I have 3 on the n-scale with about 28 servos.

#Tam valley octopus iii with rocrail code#

In the closed position the switch pulls the wire low and in the open position an internal pullup resistor in the SX keeps the line high. (This is for the Original Octopus based on the SX chip) The control code in SX/Basic can be downloaded by clicking here. I use the Octopus 3s on both my N-scale door switching layout and the HO garage layout I am building. The SX receives inputs from switches (BT1-8) connected to ground on one side. To program virtual peripherals and is well suited for this application. Not work on this board, so only purchase it if you are interested in The more expensive SX-Key also works but the debugging features will

#Tam valley octopus iii with rocrail Pc#

The SX-Key connectorĬan be used to program the chip from a USB port of a Windoze PC with an Sent: Tuesday, J7:51 AM To: Tam-Valley-Productsgroups.

On Behalf Of sprchrdsn.

Precisely time the pulse-widths for the servos. Octopus III Eight Servo Driver with Remote Aligner Tool The Octopus III can drive up to 8 servos to move turnouts or other devices on your layout controlled by a toggle switch, a momentary pushbutton, the output of a signal system or a DCC decoder. Microprocessor running at 20 MHz as set by the ceramic resonator X1. Input through a bridge rectifier which allows the use of DC or AC